Peugeot Fob Programming:

Peugeot Fob Programming:

Welcome to the best online Car Key information resource anywhere on the World Wide Web!

This Page offers FREE detailed advice explaining how to programme your Peugeot Remote Fob or keyless entry system. This could save you £££ incurred visiting a local Dealership. Read on for exact details of how to programme your the remote fob or keyless entry blip for your model of Peugeot.
AutoKey Squad Roadside Replacement Service for Car Keys
Remote Fob advice from AutoKey Squad Peugeot Car Key Specialist
(Technical Information supplied by Peugeot Car Key Specialists AutoKey Squad. Click Here to buy a new Peugeot Remote Fob or replacement Car Key)
AutoKey Squad Peugeot Car Key Specialist Francois Doumen explains: “This advice will work to programme a Remote Fob for a wide array of Peugeot vehicles. Some of the very latest remotes work on a new programming system, but whatever your model of Peugeot, this procedure is well worth a try before you contact a Peugeot Car Key Specialist (for example AutoKey Squad). I used it most recently to assist a French Madame visiting Highgate, North London to stay with her son. She had come across in the Tunnel and would have been stranded without my help. It was nice to be able help somebody out!”

 

 

 

 

 

PEUGEOT

106 PLIP PROGRAMMING

Procedure
1. Unlock the vehicle using the working key.
2. Press the LOCK button 2 times within 20 seconds.

CENTRAL DOOR LOCK (1 BUTTON PLIP KEY)
Procedure
1. Ensure all doors are unlocked using the key.
2. Press and hold plip key button until LED stops flashing.
3. After releasing button, LED will light constantly.
4. Press the Plip Button once, and LED will extinguish.
5. Open the door and hold the Plip key near the Ignition switch, and
press the plip button one time.
6. Turn the ignition ON, and wait 10 seconds then turn ignition OFF.
7. After 5 seconds, Plip should now operate.
CENTRAL DOOR LOCK with DEADLOCKING (2 BUTTON PLIP KEY)
Procedure
1. Ensure all doors are unlocked using the key.
2. Press and HOLD the large plip key button while the LED flashes continuously
for 20 seconds. After 20 seconds press the small deadlock button
once while still holding the large button.
3. The LED will stop flashing.
4. Release the large button and the LED will light constantly.
5. Press the large button one time, and the LED will go out.
6. Open the door and hold the Plip key near the Ignition switch, and
press the large plip button one time.
7. Turn the ignition ON, and wait 10 seconds then turn ignition OFF.
8. After 5 seconds, Plip should now operate.
1.8

KEY FOB PROGRAMMING
306 & 806(From 98MY) PLIP PROGRAMMING
Procedure
1. Turn the Ignition switch to accessory position using the key, without
the remote plip attached.
2. Hold the Plip key close to the central locking receiver mounted in the
roof console.
3. Press the large plip button, then the small plip button on the remote.
4. Repeat for second Plip key if required.
5. Turn ignition OFF.
6. After 5 seconds, Plip should now operate.

406 & 605 PLIP PROGRAMMING
The 406 deadlocking remote control has specific button controls, and if the
vehicles has two controls, one is set as primary and the other as secondary.
When replacing the Plip, a Primary or Secondary Plip are different
part numbers and must be ordered as required. The white label inside the
Plip is labelled PRIM and SEC.
Procedure
1. Turn the Ignition switch ON.
2. Press the large Plip key button (Primary Plip)
3. Within 10 seconds, press the large Plip key button (Secondary Plip)
4. If there is one remote, press the Primary plip button twice.
5. Turn ignition OFF.
6. Test Plip’s for correct operation.
NOTE : On some 406 models, Plips cannot be re-synchronised unless the
battery has been disconnected for 1 minute.
1.9
806 (Up to 98MY) PLIP PROGRAMMING
Full Programming Procedure:
1. Turn the Ignition switch to accessory position using the key, without
the remote plip attached.
2. Hold the Plip key towards the receiver at the front of the vehicle.
3. Press the large plip button, then the small plip button on the remote.
4. Repeat for second Plip key if required.
5. Turn ignition OFF.
After 5 seconds, Plip should now operate.

307 PLIP PROGRAMMING
Procedure:
1. Turn the Ignition switch to ON position using the first key.
2. Press the LOCK button for 10 seconds.
3. Remove key and wait for 10 seconds.
4. Check Plip key operation.
5. Repeat for second Plip key if required.
6. Turn ignition OFF

206 PLIP PROGRAMMING SYNCHRONISATION—BSI

Procedure
1. Insert Ignition Key.
2. Press the small Black button.
3. Switch the Ignition ON
4. Keep the lock button pressed for 10 seconds.
5. Release lock button , switch ignition OFF and remove key.
6. Close all doors and press the lock button 2 times.
NOTE : If PLIPS still do not work, start the vehicle and then turn OFF. Open
and close the door, and check PLIP again. This is also necessary after a
new BSI system is fitted.

We hope this advice from AutoKey Squad solved your Peugeot Remote Fob or Keyless entry programming problem. If your remote is faulty or still not working, you should click here for a DIRECT quote on a new Peugeot Remote Key Fob  or replacement Car Key – avoiding Dealership charges.

Alternatively click here for more online advice on Peugeot Fob programming:

Posted on by Harry
  • Our Services:

    • Stolen or Lost Car Keys Replaced
    • Quality Car Keys at
      Trade Cost
    • Locked Vehicles
      Opened fast
    • Remote Control Fob Supply & Programming
    • Broken Car Key Replacement
    • Trained Diagnostic Specialists
    • Guaranteed Quality Workmanship
  • coatofarms
  • cards
  • Video Guide:

  • Testimonials: